| Subject | Text |
| PS42V6 is a plasma tv, fault could be lower scan pcb or connectors to pdp, or a bad pdp |
| I also got a problem with PM-4230 Orion Plasma screen (not a TV) . It is called PLAVO (not VISION). |
|
|
| Need help with testing TV components | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points to |
| Sounds like the power supply may be bad. I can't find any info on that model. Contact LG to see wher |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| never had a buffer board fail on that model, have changed 32 of the pdps used in that series of plas |
| Bad PDP. |
| 50MP1 | Andy, I used to work for NEC and was the European Technical Specialist for Plasma displays. If your |
| Re: NEC RD-317, PX-RC1E | Did you ever find a programming manual? I'm looking for one too. Would appreciate any help. vendor |
| 50MP1 blank screen with backlight, green light stays on | Hi Plasma TV experts,
I have a 50MP1 that powers on, there is one bright color line show up on t |
| [quote:61dd7c8f2c="jon R"]Thx anyhow, yes i followed the flowchart religiously and all the supplies |
| Thx anyhow, yes i followed the flowchart religiously and all the supplies are present (3.3,5,60 and |
| Depending on the brand, they'll tell you the digital main, logic, and driver/e buffer boards. When y |
| POWER BOARD | Hello is it possible to send me the schema of Samsung LJ44-00068A PS-423-SD, i am a problem with my |
| [quote:30a24d7c00="Anonymous"]Hi,
These are out of warranty repairs, the PDP,s are fine as I have t |
| When I turn the tv on the 2 power on relays come on then a few seconds later the they turn off ( po |
| LG A/C SPLIT UNITS | I am trying to find the nomenclature for LG split units. Can't seem to find it on lge.com. Can anyo |
|
|
| In fact, I've bought this unit as faulty because I already bought one a few times ago and I've repai |
| Need Help - How to test boards in a plasma TV? | Hi Everyone,
I have a 42" plasma TV that wont turn on. The little research Ive done points |
| PX-42VM3G | Hi Pinkwell,
No problem, Im not sure regarding sourcing of the service manual. All i can tell you |
| z-sus | Hi,
The IC itself has no printed anything.On the cooler are some numbers like
4921qp1002b,second l |
| Check the resistor on the flat cable from PCB to PDP module. When is resistor broken try change it. |
| Hi,
when I disconnect the two power connectors which goes to the PDP, it's still doing the same t |
| Welcome to plasma's. Seems with x/y disconnected VS and Va are ok indicating a good power supply. Ho |
| Phillips 42pf9966/37 | When I push power button on side of TV I hear a click as it tries to turn on. It had a bad fuse for |
| dead goodmans gtv42p | Hi i have a goodmans gtv42p which is stuck in stand by.It uses a sumsung pdp panel S42D-YD02. when p |
| Looking for a couple of Plasma TV boards | I'm trying to fix my plasma and need the following boards to do so:
SDBD 6871QDH067B
YSUS 6871 |
| Plasma Screen SONY PFM 42B2E | Hello Everyone,
I was wondering if someone could help me out who has some knowledge on Presentati |
| 42WS90E | Hello,
The Thomson Plasma 42WS90E is actually an NEC rebadged, and yes this is 100% correct the p |
| probably a faulty pdp, have a very close look at the screen, check for any blackened pixels. had the |